Name of Post: Draftsman Gr II/ Town Planning Surveyor Gr II, Draftsman (Civil) & Tradesman (Civil)
Department: Town & Country Planning, KAMCO & Technic
Education Cat. No: 668/2021, 413/2019 & 756/2021
Question Code: 034/2022 (A)
Date of Test: 03.04.2022
1. Thickness of centre line and locus line is
A) 10cm
B) .20 cm
C) 10 mm
D) .25 mm
2. Angle is formed between two
A) angular lines
B) straight lines
C) parallel lines
D) all of these
3. Scale represent three different units such as metre, decimetre and centimetre
A) Vernier scale
B) Plane scale
C) Diagonal scale
D) None of these
4. All ellipse has _________ vertics and __________ foci.
A) two, two
B) one, two
C) one, one
D) two, one
5. Which grade of pencil is used for drawing arrow heads ?
A) 2B
B) 2H
C) 5H
D) H
6. Following is an enlarge scale
A) 1 : 2
B) 1 : 1
C) 2 : 1
D) 3 : 1
7. The front view of a line perpendicular to
A) point
B) a line of total length
C) a line of true length
D) none of these
8. 10 centimetre is ____________ decimetre.
A) 10 mm
B) 1 cm
C) 1 decimetre
D) None of the above
9. The unit measurement is in trusses for steel works and its parts in
A) kilogram
B) quintel
C) numbers
D) centimetre
10. One cubic metre of mild steel weight
A) 1000 kg
B) 7865 kg
C) 7850 kg
D) 6248 kg
11. The rate of payment is made for 100 cum (per of cum) in case of
A) rock cutting
B) earth work in excavation
C) excavation in trenches in foundation
D) all of these
12. Which area is included in floor area ?
A) varandhas
B) supported porches
C) balconies
D) walls
13. Damp proof course (DPC) is measured in
A) sqm
B) cum
C) metre
D) none of these
14. What is scrap value at the end of utility period of building ?
A) 5%
B) 10%
C) 6%
D) 3%
15. How much cum metre of cement is equal to one bag of cement ?
A) 0034 cum
B) 0.0034 cum
C) 0.034 cum
D) 0.34 cum
16. What is the name of the useful area or liveable area in building ?
A) plinth area
B) floor area
C) circulation area
D) carpet area
17. Which estimate is called item rate estimate ?
A) plinth area estimate
B) detailed estimate
C) abstract estimate
D) preliminary estimate
18. What is the unit of measurement in MKS for brick work of thin partition wall ?
A) sq inch
B) sq cm
C) sq ft
D) sq m
19. What is the unit measurement in the excavation of foundation ?
A) cum
B) sq m
C) metre
D) cum cm
20. The total estimate cost of a building sanitary and water supply work usually account for
A) 3%
B) 18%
C) 8%
D) 10%
21. The increase in volume of dry sand when water is added is called
A) Honey combing
B) Bulking
C) Segregation
D) Bleeding
22. The aggregate is called coarse aggregate if it is completely retained on
A) 475 mm seive
B) 15 mm seive
C) 219 mm seive
D) 4.75 mm seive
23. The compressive strength of stone is found out by
A) Attrition test
B) Crushing test
C) Hardness test
D) Impact test
24. The quantity of one bag of cement is
A) 0.035 m3
B) 0.35 m3
C) 0.0035 m3
D) 3.05 m3
25. The Kiln used for the manufacture of terra-cotta is
A) Rotary Kiln
B) Blast Furnace
C) Muffle Furnace
D) lntermittent Kiln
26. The compressive strength of fire-bricks varies from
A) 200 to 220 N/mm2
B) 30 to 35 N/mm2
C) 20.00 to 22.00 N/mm2
D) 2000 to 2200 N/mm2
27. The heating of limestone to redness in contact with air is known as
A) Hydraulicity
B) Calcination
C) Setting
D) Slaking
28. An example for shrinkage-reducing admixture is
A) Propyline glycol
B) Lignosulfonates
C) Tartaric acid
D) Asphalt
29. The part of tree, which hold together the annual rings of Hard wood and Sap wood is
A) Medullary rays
B) Inner bark
C) Annual rings
D) Cambium layer
30. The carbon content of steel is
A) 1.0 to 2.5 Percent
B) 0.10 to 0.25 Percent
C) 10 to 25 Percent
D) 0.01 to 0.025 Percent
31. The most common material used as vehicle of a paint is
A) Nut oil
B) Poppy oil
C) Tung oil
D) Linseed oil
32. The ability of materials to get stretched into a wire by pulling or drawing is
A) Ductility
B) Malleability
C) Brittleness
D) Fatigue
33. Horizontal Projections of head or sill beyond the face of door and window frame is
A) Head
B) Horn
C) Style
D) Rail
34. The window which is provided in a room which has greater ceiling height than the surrounding room
A) Clere-storey window
B) Bay window
C) Dormer window
D) Lantern window
35. A short sections of wood or steel which are fixed on the principal rafters of trusses to support the purlin is
A) Template
B) Post plate
C) Cleats
D) Wall plate
36. The process of joining two wooden members at an angle is called
A) Scribing
B) Housing
C) Rebatting
D) Mitring
37. In a residential building , the average value of stair width is
A) 700 mm
B) 900 mm
C) 1000 mm
D) 800 mm
38. In ordinary residential building the DPC may be provided
A) Between ground level and water table level
B) At ground level
C) At plinth level
D) At sill level
39. Which chemical is used as a soil treatment in termite proofing ?
A) Aldrin
B) Chlorine
C) Bromine
D) Potassium hydroxide
40. Type of bond in brick masonry consisting of alternate course of headers and stretchers is called
A) Flemish bond
B) Heading bond
C) Stretching bond
D) English bond
41. The portion of the brick left after removing the corner equal to half the width and half the length
A) Closer
B) King closer
C) Queen closer
D) Mitred closer
42. The portion of the wall which support an arch is wall which
A) Abutment
B) Column
C) Pier
D) Skew back
43. An arrangement for supporting an unsafe structure temporarily, till it is rendered safe of dismantled
A) Scaffolding
B) Shoring
C) Jacking
D) Underpinning
44. When two footings are connected by a beam the, foundation is called
A) Combined footing
B) Mat footing
C) Strap footing
D) Strip footing
45. The corresponding proportion of M 7.5 concrete is
A) 1 : 1½ : 3
B) 1 : 2 : 4
C) 1 : 4 : 8
D) 1 : 5 : 10
46. Slump height of concrete for canal lining is
A) 20 to 40
B) 70 to 80
C) 25 to 50
D) No slump
47. Pile which are driven to an inclination to resist large horizontal or inclined forces is
A) Fender piles
B) Anchor piles
C) Batter piles
D) Tension piles
48. An example for four centered arch is
A) Florentine arch
B) Venetion arch
C) Ogee arch
D) Horse shoe arch
49. The maximum strength out of the shearing and bearing strength of the rivet for a particular joint is
A) Rivet - value
B) Shear strength
C) Tearing strength
D) Efficiency of joint
50. As per IS 456, Modular ratio for M30 grade concrete is
A) 10
B) 9.33
C) 3.66
D) 6.75
51. The sign convention for bending moments is that a beam in “hogging” condition is
A) Positive
B) Negative
C) Positive or Negative
D) None of these
52. Nominal cover provided for concrete exposed to moderate exposure should not be less than
A) 75 mm
B) 40 mm
C) 45 mm
D) 30 mm
53. ___________ is to make clear that which is not perfectly evident from numerals and sketches.
A) Data book
B) Explanatory notes
C) Map
D) Symbols
54. The difference between two measured value of the same quantity
A) True error
B) Accuracy
C) Discrepancy
D) None of these
55. Which of the following instrument is used radio wave for distance measurement ?
A) Geodimeter
B) Telluro meter
C) Radiography
D) None of these
56. lS CODE for metric surveying chain
A) lS 1464-1970
B) lS 1492 -1970
C) lS 1491-1970
D) IS 1462-1970
57. If the chain is stretched out of the line the measured distance will always be
A) Less
B) More
C) Equal
D) None of these
58. The true bearing of a line is a ___________ quantity.
A) Varying
B) Constant
C) Non predictable
D) None of these
59. The whole circle bearing of a line is 170 degree 12 minute what will be the reduced
bearing
A) 9 degree 48 minute
B) 10 degree 14 minutes
C) 9 degree 30 minutes
D) 9 Degree 88 minutes
60. When the distance between the two point and the instrumentation is either too large or cannot be measured which method is used in plane table ?
A) Radiation
B) Intersection
C) Resection
D) traversing
61. ____________ is a line passing through out on the surface of the ground and preserving a constant inclination to the horizontal.
A) Datum
B) Slope
C) Contour gradient
D) All of these
62. The prismoidal correction is always
A) Additive
B) Zero
C) Subtractive
D) None of these
63. ________ the method is based on the principle that the angle between the tangent and the chord is equal to the angle which that code is subtended in the opposite segment.
A) Offsets from the tangent
B) Rankines method
C) Two theodolite method
D) None of these
64. __________ of a survey line may be defined as its co-ordinate length measured parallel to an assumed Meridian direction.
A) Latitude
B) Departure
C) Altitude
D) None of these
65. ___________ aIIows the user to capture collect and transform spatial and the thematic data into digital form.
A) Data storage system
B) Data manipulation
C) Data input system
D) None of these
66. Which program is used for erecting perpendicular line to base line ?
A) Stakeout
B) PlayStation
C) Reference line
D) The distance
67. What is the distance of the load from the fulcrum called ?
A) Load distance
B) Moment
C) Load arm
D) None of these
68. The work done in unit time is called
A) Newton
B) Power
C) Dyne
D) Force
69. One metric HP is ___________ watts.
A) 735.5
B) 700.3
C) 753.5
D) 753.3
70. The capacity of a body to do work is known as
A) Work
B) Power
C) Energy
D) None of these
71. How many litres of water in a cylindrical tank of radius 75 cm and height 100 cm can hold ?
A) 1765.25 lit
B) 1763.5 to litres
C) 1766.25 lit
D) 1760.25 l
72. Deformation per unit length in the direction of force is known as
A) Strain
B) Lateral strain
C) Linear strain
D) Linear stress
73. The axis used to show depth in AutoCAD
A) W axis
B) X axis
C) Y axis
D) Z axis
74. Which command convert discrete object in polyline ?
A) Union
B) Subtract
C) Join
D) Polyline
75. ________ sets the spacing between the dimension lines of a base line dimension.
A) Line type
B) Spacing
C) Base line spacing
D) None of these
76. What setting gradient allows us to fill an open area ?
A) Gap
B) Tolerance
C) Transparency
D) Open
77. Which of the following file extension cannot open the AutoCAD ?
A) dwg.
B) dxfc.
C) dot
D) dws
78. What is the minimum allowable number of layers in a drawing ?
A) 0
B) 5
C) 1
D) 2
79. Which of the following is not a property of an object ?
A) Line weight
B) Measure
C) Hyperlink
D) Elevation
80. The mechanical advanlag of an ideal machine is 100. For moving the local through 2 m, the effert moves through
A) 0.02 m
B) 2 m
C) 2.5 m
D) 20 m
81. The percentage of C.C.A. proposed to be irrigated seasonally is called
A) Gross Commanded Area
B) Uncultivated Area
C) Culturable Uncultivated Area
D) Intensity or irrigation
82. When seepage water is sufficient for the growth of the crop and if no addition surface watering is necessary, such a dam is called
A) Debris dam
B) Diversion dam
C) Water spread dam
D) Gravity dam
83. Ganga Canal System is an example of
A) Direct irrigation
B) Storage irrigation
C) Combined direct and storage
D) None of the above
84. An opening provided in one side of a reservoir, with upstream liquid level below the top edge of opening is called
A) Orifice
B) Notch
C) Weir
D) Mouthpiece
85. Structure provided to protect the land and property which is likely to be submerged during ponding of water of during floods is
A) Groynes
B) Divide wall
C) Marginal embankments
D) Under-sluice
86. Mechanism that receives data from the wind vane and instructs the wind turbine to rotate to be facing the wind is called
A) Anemometer
B) Controller
C) Yaw motor
D) Yaw drive
87. When wheels slide without revolving the phenomenon is called
A) Skiddin
B) Sliding
C) Slip
D) Spalling
88. Recommended land width of major district roads in open areas in plain and rolling terrain in meters
A) 15
B) 20
C) 25
D) 45
89. The method of construction of cement concrete roads where entire width of the road is constructed continuously from one end to the other is called
A) Strip method
B) Continuous bay method
C) Full width method
D) All of the above
90. Culvert suitable in high discharge areas and low debris flow areas are
A) Arch culvert
B) Box culvert
C) Pipe culvert
D) None of the above
91. Which pier is adopted, if the longitudinal beams or girders of the superstructure of bridge are closely spaced ?
A) Dumb-bell piers
B) Cylinder piers
C) Pile bents
D) Column bents
92. Structure made of stones or concrete blocks or mattresses, placed on the bottom or banks of a river for minimizing and controlling the erosion
A) Scuppers
B) Revetment
C) Apro
D) Cribs
93. Standard size of ballast for C.T.S.-9 and steel sleepers
A) 20 mm
B) 25 mm
C) 40 mm
D) 50 mm
94. The defect caused when the rail with its end or ends bent in vertical direction is called
A) Wear of rails
B) Bending of rails
C) Hogging of rails
D) Creep of rails
95. Which is the structure constructed in the form of a chamber along the sewer line to admit clear rain water into the combined sewer ?
A) Catch basin
B) Drop manhole
C) Clean out
D) Trap
96. Slow sand filter is unsuitable for waters having turbidity more than
A) 40 ppm
B) 50 ppm
C) 60 ppm
D) 75 ppm
97. What is the yield of rapid sand filters as compared to slow sand filter ?
A) 15 times
B) 25 times
C) 30 times
D) 45 times
98. Water taps are also known as
A) Bib cocks
B) Goose neck
C) Ferrule
D) Stop cocks
99. Valves provided to remove the accumulated silt is called
A) Mud valve
B) Scour valve
C) Blow off valve
D) All of the above
100. The sloped floor of a manhole or inspection chamber on both side and above the
top of the channel is called
A) Bedding
B) Barrel
C) Cleaning eye
D) Benching
No comments:
Post a Comment